Pool Equipment · 10 min read

How to Level a Pool Table: Frame, Legs, Shims and Slate

Published November 10, 2026 · Tolerances from the WPA Recommended Equipment Specifications · Assembly steps from Brunswick installation manuals · The slow-roll example is our calculation

Level the frame first, then the slate. With the table where it will stay, find the highest corner with a level and bring the other three up to it, using the leg levellers or hard shims under the legs. If the bed is still out after that, the fix is under the cloth: each slate section is wedged level against the frame, the middle section is shimmed flush with the two ends, and the seams are filled with beeswax or hard putty.

How level? The WPA's specification for tournament tables asks for a bed flat within ±0.020 in (0.51 mm) along the length and ±0.010 in (0.25 mm) across the width, with slate seams within 0.005 in (0.127 mm). A 12-inch machinist's level, graduated at about 0.42 mm per metre, is the tool for checking that. A rolling ball is not.

An out-of-level table rarely shows on a firm shot. It shows on the slow ones: the ball you nursed toward the pocket that turned away at the last moment, the lag that always drifts toward the same cushion. Levelling is two separate jobs, and most of the frustration comes from mixing them up. The legs decide whether the whole table is tilted. The slate, and the shims under it, decide whether the bed is flat. You can do the first on your own with a level and a spanner. The second means taking the cloth off.

What you need

A phone level app is fine for rough work on the frame. Its accuracy depends on the phone's sensor and on calibrating it, and even a reading of 0.1° is 1.7 mm per metre, about four graduations on a machinist's level.

Check the level before you trust it

Any level can be slightly out. Put it on one spot on the bed, note which way the bubble sits, then turn the level end for end on exactly the same spot and read it again. A tilt in the table sends the bubble toward the high end of the table both times. An error in the level sends it toward the same end of the level, so after you turn it round it shows up at the other end of the table. If you see that, adjust or replace the level first; Starrett's machinist's levels have adjustable vials for this reason. Skip this step and you can spend an afternoon levelling the table to the error in your tool.

Take your readings on the bed: the bare slate before it is covered, or the cloth after. Not on the rails. The rails are separate pieces bolted to the slate, and the tops of them are not the playing surface.

Tilt is fixed at the legs, flatness at the slate

BASE FRAMESlate, 3 sectionsSeams filled flushClothWedges, frame to slateLeveller: screwout to raiseor a hard shimfloor slope exaggerated
Figure 1: what each adjustment does (not to scale). Levellers or shims under the legs tilt the whole table. Wedges between the frame and the slate set each section flat and flush with its neighbours.

Turning a leg leveller lifts one corner of everything above it, so it changes the tilt of the whole bed, both along and across. It cannot fix a dip in the middle or a step at a seam. Those are fixed under the slate, which is why a table that is perfectly level at the legs can still roll off in one spot.

level, lengthwise and crosswisestraightedge across a seamseam between slate sections
Figure 2: where to check a three-piece bed. Read the level both lengthwise and crosswise near each end and the middle of every section, and lay a straightedge across each seam in a few places.

Step 1: level the frame at the legs

Put the table in its permanent position first. Brunswick's instructions level the base frame only once the table is where it will stay, and even a short move across a floor changes the readings.

Then find the highest corner with your level and bring the other three up to it. That is the method in Brunswick's manuals, and it makes sense: working up from the highest corner, you only ever raise, so you never run out of adjustment at the wrong end. Raising one corner changes the reading in both directions, so check lengthwise and crosswise after every adjustment and make small turns as you get close.

Adjustable legs

Before the table is stood up, Brunswick's Black Wolf Pro instructions have you thread each leveller all the way into the leg and then back it out two full turns, so there is travel in both directions. If your levellers are already wound out a long way on one side, that corner of the floor is low, and you may need a shim under that leg as well.

Shims under the legs

If the legs have no levellers, use shims. Brunswick's Allenton manual levels the base frame by putting the supplied shims under the other three legs. Use hard, flat shims that sit under the whole foot. Cardboard and folded paper are tempting, but they can keep compressing under the weight of a slate table.

Before you go on, press down on each corner. If the table rocks, one leg is not carrying its share of the weight, and the frame can twist when someone leans on it. Bring the light leg down until all four bear, then check the level again.

Uneven floors

Almost no floor is truly level, and that is what levellers and shims are for. It helps to check the floor before the table goes in: lay a long level on the floor where each leg will stand to see which corner is highest and roughly how far the others drop. If the drop is more than the levellers can take, put a solid, flat block or a stack of hard shims under the low legs to bring them within range, then finish with the levellers. On carpet, the legs can keep sinking into the pile and underlay for a while, so check again after a couple of weeks.

Step 2: level the slate

This step needs the cloth off, so it happens when a table is installed, moved or re-covered, or when the frame reads level and the bed still does not. Brunswick's installation manuals describe the order for a three-piece slate:

  1. Place the centre section square on the frame, with an equal overhang on both sides.
  2. Place the two end sections and screw them down at the ends of the table.
  3. Level each end section by driving wooden wedges between the top of the frame and the underside of the slate, as close to the countersunk screw holes as possible, loosening and retightening the screws as you go.
  4. With both end sections level, fasten them at the joints and check again. If a section has moved, back the screws out, move the shim and retighten.
  5. Shim the centre section until it sits flush with both end sections, then screw it down.
  6. Fill the joints with fast-setting hard putty, beeswax or slate joint wax, and sand or scrape across them so they are flush.

The two end sections set the plane, and the middle one is fitted to them. The WPA specification asks for the joints to be in the same plane within 0.005 in (0.127 mm) after levelling and shimming. Lay the straightedge across the seam: if the 0.005 in feeler blade slides under it on the low side of the joint, the step is at the WPA limit or over it. The filler does not fix a step. Wax or putty only fills the gap; a section that sits high or low has to be corrected with the shims under it.

After that the cloth goes back on, and its tension matters too: see pool table cloth.

One-piece or three-piece slate

For WPA events the slate must be three pieces of equal size, at least 1 in thick, with a wooden frame at least ¾ in thick attached underneath and fixed to the base with countersunk screws or bolts. Three pieces can each be shimmed to the frame, which takes up small errors in the frame; the seams are the price.

A one-piece slate has no seams to line up, so most of the adjustment happens at the legs. Dr. Dave Alciatore's pool FAQ puts it simply: a one-piece slate is easier to level but much heavier and harder to move, and once three pieces are levelled properly with the seams waxed smooth, the difference is small. Tables with a wood or composite bed instead of slate can only be levelled at the legs; if the bed itself has sagged, shims under the legs will not make it flat.

How level is level enough?

The best-known numbers come from the WPA's Recommended Equipment Specifications, which have been in effect since November 2001. Section 3 says the table should be built to stay stable and level under all conditions of play, and section 4 sets the slate figures:

WPA requirementFigure
Slate thicknessat least 1 in (25.4 mm)
Flatness along the lengthwithin ±0.020 in (0.508 mm)
Flatness across the widthwithin ±0.010 in (0.254 mm)
Extra sag with 200 lb (90.7 kg) at the centreno more than 0.030 in (0.762 mm)
Slate joints, after levelling and shimmingin the same plane within 0.005 in (0.127 mm)
Tournament slatethree pieces of equal size, a wooden frame at least ¾ in (19 mm) thick underneath, fixed with countersunk screws or bolts

WPA Recommended Equipment Specifications (effective November 2001), section 4, Slates.

Two things to bear in mind. First, the document sets standards for WPA championships and sanctioned events and says it does not necessarily apply to tables made for home use. Second, it describes flatness, which is not quite the same as level: a perfectly flat slate can still be tilted. If you read the band as measured from true level, ±0.020 in along 100 in allows up to 0.040 in from one end to the other (about 1 mm over 2.54 m), and ±0.010 in across 50 in allows 0.020 in from side to side. Both work out at about 0.4 mm per metre, roughly one graduation on a 12-inch machinist's level and about the rated accuracy of a good spirit level. The Billiard Congress of America has its own equipment specifications, often quoted with the same numbers; we cite the WPA's because it is the document we could read in full.

The rulebooks accept that tables are not perfect. CSI's applied rulings say a tournament match may have to start or carry on at a dirty or unlevel table, that the referee or the organisers decide, and that the organisers should get the problem fixed as soon as they can.

For a home table, a sensible target is the bubble centred on a machinist's level at every point in Figure 2, both ways round, and no step at a seam that the 0.005 in blade can find. Past that point, the cloth and the balls make more difference than another shim.

How much does a small tilt bend a slow ball?

This is our own calculation, and these are its assumptions:

For a slow roll that stops after a distance D, the sideways drift comes out at about (5/7) × g × slope × D ÷ (2 × 0.1 m/s²). We checked that against a step-by-step simulation of the same model. For a 2.3 m roll, about the length of a 9-foot bed:

Tilt across the ball's pathRise across a 9-ft bed (1.27 m)Slow roll that stops after 2.3 m: sideways driftFirmer roll (would run about 7 m): drift after 2.3 m
0.1 mm per metre0.13 mm8 mm1.5 mm
0.2 mm per metre0.25 mm16 mm3 mm
0.4 mm per metre0.51 mm32 mm6 mm
0.8 mm per metre1.0 mm65 mm12 mm

Our calculation, with the assumptions listed above. A pool ball is 57.15 mm across; in a 116 mm corner pocket it has about 29 mm of room either side.

Look at the 0.4 mm row. A tilt of 0.4 mm per metre, which is about one graduation on a machinist's level and half a millimetre from one side rail to the other, bends a dying ball by 32 mm over the length of the table. That is more than the room a ball has in a pocket, so a slow ball aimed at the middle of a corner pocket can still miss. The same tilt moves a firmer roll by about 6 mm, a fifth of that room.

The bend is not spread evenly. In this model more than half of it happens in the last quarter of the roll, because the ball keeps the same sideways pull while it slows down. That is why roll-off looks like a ball "falling off" just before it stops. On faster cloth a slow ball rolls for longer, so the same tilt bends it more: at 0.07 m/s² instead of 0.1, the 32 mm becomes 46 mm.

Checking without a level: the rolling-ball test

Rolling a ball slowly down the table is the classic way to check a table without a level, and the numbers above show it is sensitive. The trouble is that it is sensitive to everything. Dr. Dave's FAQ defines table roll-off as the change in course of a slow-rolling ball, and lists the causes as a non-level or irregular playing surface, dirt or chalk dust on the table, and an unbalanced cue ball. A ball that turns tells you something is wrong, not which thing.

Your hand is another source of error. Release a ball 1° off line and it ends up 40 mm to the side after 2.3 m, more than a 0.4 mm per metre tilt would move it, and fingers can easily put a little spin on it as well. A roll also only tells you about its own path, on average: it cannot show where the low spot is, and a dip and a rise along the same line can partly cancel each other out.

If you want the test to mean something:

Used like that, the rolling ball is a good final check after levelling with a level, and a quick way to decide whether it is worth getting the level out. It is a poor tool for doing the levelling itself.

Snooker tables

The WPBSA's Official Rules (September 2024 edition) set the playing area of a full-size table at 3569 × 1778 mm and the height at 864 mm from the floor to the top of the cushion rail, each within ±13 mm, and say that where the cloth has a nap, it runs from the baulk cushion to the top cushion. They say nothing about how flat or level the bed must be. Riley describes the sectional slate bed as a skilled job to install and level, needing at least two people and at least four to five hours for a full-size table. The principle is the same as on a pool table, frame level at the legs and slate sections set flat and flush, but with a much bigger and heavier bed it is a job for a fitter.

Be careful with roll tests on napped cloth. The nap is widely said to affect slow balls differently with and against it, so a roll up the table and a roll down it are not a clean comparison. We have not found a measured figure for the size of the effect. On a snooker table, trust the level.

Common mistakes

When to call a table mechanic

Call one when the frame reads level and the bed still does not: a dip, a hump, or a step you can feel at a seam. The fix is under the cloth, which means taking the rails and cloth off, re-shimming and re-filling the slate, and putting the cloth back on or replacing it. Unless you are ready to re-cover the table yourself, that is a mechanic's job. The same goes for moving a table (the slate has to come off and the whole table is levelled again in its new place), for cracked slate, for slate that moves when you press on it, and for loose slate screws. For a snooker table, start with a fitter.

A perfectly level table to practise on

The table in AimGeometry, our free browser trainer, has no tilt and no worn tracks, so when a slow ball misses, it was the aim or the speed. It draws the aim line and the ghost ball and tells you how far off each shot was.

Start the straight-in drill →

FAQ

Can you level a pool table by yourself?

The frame, yes: with a precision level and a spanner, one person can find the highest corner and raise the other three with the leg levellers or shims. Levelling the slate means taking the rails and cloth off and lifting heavy, brittle slate sections, so you need a helper or a table mechanic.

How do you level a pool table with adjustable legs?

Put the table in its final position, find the highest corner with a level on the bed, and screw out the levellers on the other three corners until the level reads true both lengthwise and crosswise. Check both directions after every adjustment, because raising one corner changes both.

How do you level a pool table on an uneven floor?

The same way, with more adjustment. If the floor drops more than the levellers can take, put a solid block or hard, flat shims under the low legs to bring them within range, then finish with the levellers. On carpet, check again after a couple of weeks.

How do you check if a pool table is level without a level?

Roll a clean ball slowly along several lines, releasing it the same way each time (a small ramp helps), and roll each line from both ends. A tilt pushes both rolls to the same side of the table. The test also reacts to dirt, an unbalanced ball and your release, so use it as a check, not to do the levelling.

How level should a pool table be?

The WPA specification for tournament tables asks for a playing surface flat within ±0.020 in (0.51 mm) along the length and ±0.010 in (0.25 mm) across the width, with slate seams in the same plane within 0.005 in (0.127 mm). For a home table, aim for a centred bubble on a machinist's level at several points, both ways.

Do you level a pool table on the rails or on the slate?

On the slate, or on the cloth over it. The rails are separate pieces bolted on, and their tops are not the playing surface.

Advertisement

Related reading: Pool Table Cloth · Pool and Snooker Ball Sizes · Billiards vs Pool vs Snooker · Chinese 8-Ball Table Size and Pockets · How to Aim in Pool

Sources: WPA Recommended Equipment Specifications, effective November 2001 (section 1 purpose and scope, section 3 design, section 4 slates: thickness, flatness ±0.020 in lengthwise and ±0.010 in across, deflection under 200 lb, joints within 0.005 in, three-piece tournament slate; section 6 rail bolts); Brunswick installation manuals for the Allenton, Shorewood, Danbury, Tahoe and Amherst tables (September 2006) and the Black Wolf Pro (October 2020), for the order of levelling the base frame, wedging and shimming the slate and filling the joints; CueSports International, Official Rules effective June 1, 2023, applied ruling 1-2 (acceptance of provided equipment); WPBSA Official Rules of the Games of Snooker and English Billiards, September 2024, Section 1 Rule 1; Riley Snooker International, installations page (two people, four to five hours, levelling a skilled job); Dr. Dave Alciatore, drdavepoolinfo.com FAQ pages on table roll-off, slate and cloth speed (Bob Jewett's lag-timing method) and pool physics property constants (rolling resistance 0.005–0.015), read November 10, 2026; level accuracies from the Starrett 98-12 product page (80–90 seconds, 0.005 in per foot, 0.42 mm per metre) and the Stabila Type 70 specification (0.5 mm per metre, normal position). The drift figures are our calculation for a ball rolling without slipping at a constant 0.1 m/s² deceleration, checked with a step-by-step simulation. This article contains no sponsored or affiliate links.

Advertisement