Pool & Snooker Equipment · 10 min read

How to Replace a Cue Tip: When to Do It, Which Glue, and How to Shape It

Published November 17, 2026 · Method based on Dr. Dave Alciatore's no-special-tools procedure (Billiards Digest, May 2021) · Shape and miscue facts from his cue tip FAQ · No brands recommended

Most tips that play badly need reshaping, not replacing. Replace a tip when there is almost no leather left above the ferrule, when it splits or its layers start to separate, or when scuffing no longer makes it hold chalk. A flattened dome, a glazed surface and an edge that has mushroomed over the ferrule can all be fixed on the tip you already have.

The job itself: cut the old tip off, scrape the ferrule end clean and flat, sand the back of an oversized new tip flat, glue it on centred with cyanoacrylate (super glue) gel and hold it under firm pressure until the glue sets, then trim and sand the sides flush with the ferrule and shape the dome. A knife, sandpaper, tape and glue are enough to do it at home; a cue repairer with a lathe does it faster and more accurately.

Replace or reshape? Check the tip first

Look at the tip side-on in good light, then run a finger from the ferrule up onto the leather. Five conditions cover almost everything you will find, and only the last two need a new tip.

ConditionWhat you seeWhat to do
Flattened domeFrom the side, the top looks level instead of curvedReshape it (see the shaping section)
Glazed surfaceShiny, hard-looking leather; chalk won't stay onTap or scuff it lightly. If it still won't hold chalk, replace it
MushroomedThe leather bulges past the ferrule; you can feel a lipSand it back flush and burnish the side
Worn thinVery little leather left above the ferruleReplace it
Damaged or looseA split, a piece missing, layers peeling apart, or the tip moving on the ferruleReplace it

A thin tip is worth replacing before the ferrule gets anywhere near the ball, and not only to protect the ferrule. Dr. Dave Alciatore notes that the shorter a tip is cut or worn down, the harder it plays, and that soft tips harden with use. If an old tip feels noticeably harder than it used to, check how much leather is left before you blame the tip model.

Glazing is the surface packed down and polished by thousands of hits on the cue ball. The old rec.sport.billiard FAQ, quoted on Dr. Dave's site, puts the cure in four words: tap more, scuff less. A tapping tool roughens the surface without taking much leather off; sandpaper works but wears the tip away quickly. Day-to-day chalking and scuffing are covered in chalk and tip maintenance, so this guide sticks to shaping and replacing.

How often should you replace a cue tip?

There is no fixed interval. Retailers' rules of thumb (two to four months for someone who plays several times a week, six months to a year for a casual player) are estimates of how much you play, not tested lifespans. A tip lasts as long as its leather, and three things use the leather up: hitting balls, especially with a soft tip; shaping, because every pass of a shaper removes some; and scuffing. Dr. Dave's FAQ says a hard tip that is chalked before every shot and shaped or scuffed as little as possible can last several years of regular play. A soft tip used every day will not come close.

Our suggestion: fit a new tip a few sessions before a match rather than the night before, so you have played with it and know it is holding before it matters.

What you need

This is the kit for the hand method below, with no lathe and no special tools:

How to replace a cue tip, step by step

This is Dr. Dave Alciatore's method, published in Billiards Digest in May 2021 and developed with help from Bob Jewett, in our own words. Rest the shaft on a folded towel on a table for most of the job; it keeps the shaft steady and lets you roll it.

  1. Cut off the old tip. Put the blade close to the ferrule but not on it, so that a thin layer of leather stays behind, and cut with a sawing motion while rolling the shaft. Don't try to get it all in one cut. A nick in the ferrule is permanent.
  2. Scrape the ferrule end clean and flat. Take off the remaining leather and old glue a thin sliver at a time, with the blade flush against the end of the ferrule, scraping rather than cutting as you get close. Then sand lightly: press medium sandpaper onto the centre of the ferrule with a fingertip and turn the shaft, keeping away from the outer edge so you don't round it off. Wipe off the dust, with acetone if you have it. The end has to be flat. If the new tip rocks on it, the ferrule needs facing on a lathe, and that is shop work.
  3. Prepare the new tip. Sand its back flat with a circular motion, turning the tip as you go; this also gives the glue a fresh surface to soak into. Wipe off the dust and don't touch either gluing surface again. Check that the tip sits flat on the ferrule without wobbling and overhangs it all the way round.
  4. Tape the ferrule. Wrap tape around the ferrule until its diameter matches the tip's. The tape keeps glue off the ferrule and gives you an edge to centre the tip against. Bring it right up to the end of the ferrule but not past it, or the tip won't sit flat.
  5. Glue it on. Spread gel evenly over the back of the tip and add a small drop in the middle, so the glue squeezes out evenly with no gaps or bubbles. Set the tip on the ferrule, centre it against the tape with small turns and nudges, press gently until glue appears all round, and wipe off the excess.
  6. Hold firm, even pressure. Push the shaft straight down, tip first, onto a board on the floor, or wedge it upright under a table, so the pressure is square to the tip. The gel sets in about a minute; give it the full cure time printed on the pack before you hit hard shots with it.
  7. Peel off the tape, pulling towards the tip and lifting stubborn edges with a fingernail or the knife.
  8. Trim the overhang. Hold the shaft tip-down with the blade flush against the side of the ferrule and take small sawing cuts, a little at a time, without forcing the blade. Keep a little downward pressure on the tip as you cut, so you don't lever its edge off the glue. Leave some excess; the sanding removes the rest.
  9. Sand the sides flush. Put a fresh layer of tape on the ferrule. Lay coarse sandpaper on the table, stand the wooden block on it, and tape printer paper over the rest of the sheet, so the only abrasive left showing is a strip between block and paper as wide as the tip is thick. Lay the shaft down with the tip against the block, so the leather touches sandpaper while the taped ferrule rides on paper, and rub back and forth, turning the shaft often. Change to fine paper as the tip gets close to the ferrule's diameter. Take the tape off and check: there should be no ledge at all between leather and ferrule. Finish with very fine paper or emery wrapped around tip and ferrule together.
  10. Burnish, shape and chalk. Wet the side of the tip and rub it on the paper, or on a piece of leather, to seal and smooth it. Then shape the dome (next section), smooth it lightly with fine paper, and chalk it thoroughly.

Two warnings are worth repeating. The ledge in step 9 is not cosmetic: Dr. Dave points out that a lip between tip and ferrule can catch on something and pull the tip off, and that on a tip which has also mushroomed, the edge can tear on a hard shot far from centre. And a layered tip is itself held together by glue. Kamui's installation guide says its layer glue starts to soften once friction heats the tip above 60 °C, so sand and burnish in short spells, check the heat with a finger, and don't spin the tip hard against abrasive.

If the tip slid off-centre while the glue set, the overhang is your margin: sand it back to a full circle and nobody will know. If part of the ferrule end ends up uncovered, cut the tip off and start again.

Which glue for a cue tip?

A cyanoacrylate (super glue) gel. It is what Dr. Dave's method uses, and his FAQ says any CA gel will do as long as it isn't old. Freshness matters more than the brand, so buy small single-use tubes from a shop that sells plenty of them. The gel form matters too: it stays where you put it instead of running down onto the ferrule.

Two tips from repairers quoted on the same FAQ page. Cyanoacrylate cures by reacting with moisture, so breathing on both surfaces just before you press them together helps it set. And a soft, dry tip can soak up glue and leave the joint short of it, so some installers rub the back of the tip in a drop of glue, let it dry, sand it lightly and then glue as normal.

The older alternative is a contact-type tip cement, and it goes on differently: a thin coat on both the tip and the ferrule, a wait until it turns tacky, then the tip pressed on firmly and left before trimming (the widely sold "ten-minute" kind asks for ten minutes). Pick one type and follow the directions on the pack. With either, a clean, flat ferrule end and a flat tip back do more for the joint than the choice of glue.

How to shape a cue tip: dime or nickel?

Players describe the dome by the coin whose edge matches it when you hold the coin up beside the tip. The rule of thumb from pool engineer Patrick Johnson, quoted on Dr. Dave's site, is a curvature radius smaller than the tip's width, so the tip never meets the ball on its edge: roughly a quarter for a 13 mm tip, a nickel for 12 mm and a dime for 10 mm. A UK 5p is almost exactly a dime.

CoinDiameter, edge radiusSuits tips of about
Dime (US)17.91 mm, radius 8.95 mm10 mm or less: snooker, UK pool
5p (UK)18.00 mm, radius 9.0 mmthe same as a dime
1p (UK)20.30 mm, radius 10.15 mmbetween a dime and a nickel
Nickel (US)21.21 mm, radius 10.6 mm12 mm
Quarter (US)24.26 mm, radius 12.13 mm13 mm (most American pool cues)
10p (UK)24.50 mm, radius 12.25 mmthe same as a quarter

Coin diameters from the US Mint and the Royal Mint; the radius is half the diameter. The tip sizes follow Patrick Johnson's rule of a radius smaller than the tip's width.

What the shape does not change matters as much as what it does. For a given contact point on the cue ball, every tip shape gives the same spin, and the miscue limit sits at about half the ball's radius from centre whatever tip you use; Johnson calls that "about where the miscue limit is no matter what the size or shape of your tip". The measured effects of tip size and hardness are in cue tip size and hardness.

So why keep a dome at all? Because a flat tip changes where the tip touches the ball. A perfectly flat face meets the cue ball at the point in line with the ball's centre, so moving the cue off-centre by up to half the tip's width doesn't move the contact point at all; go further and the square edge of the tip hits the ball instead. That is the rec.sport.billiard FAQ's explanation, and it is why a flattened tip skids on spin shots: it reaches the ball with its edge. Keeping the dome is about avoiding edge contact, not about getting more spin.

Shape with a tip shaper or with coarse sandpaper curled in your hand, turning the cue as you go and working from the edge up towards the crown so you don't sand the top flat. Check against the coin often. Keep the crown in the middle of the tip: Dr. Dave lists an off-centre crown as a source of unintended side spin. Then stop. Every pass takes leather off, so reshape when the dome has visibly flattened, not as a habit.

Mushrooming: trim it, and notice what it is telling you

Mushrooming is the leather spreading sideways under impact until the tip is wider than the ferrule. Softer tips do it more because they compress more; Dr. Dave notes that hard tips hold their shape better over time.

On a properly shaped tip hit inside the miscue limit, the very edge never touches the ball, so the bulge itself doesn't spoil shots. It is still worth removing. The lip can catch, the overhang is unsupported leather that can tear on a hard off-centre hit, and a lopsided tip is a distraction when you are lining up. Tape the ferrule and sand the side back flush with very fine paper (600 grit or finer), or use the block-and-paper set-up from step 9, then burnish the side. A slight bevel at the top edge is fine; Dr. Dave notes it leaves room for the next round of mushrooming.

If a tip mushrooms again soon after you trim it, or its edge starts to split, that is the time for a new tip, perhaps a harder one.

Do it yourself or take it to a shop?

Dr. Dave is plain about this: if you have a reliable cue mechanic nearby, that is the best option, and the hand method is for when you need a tip fast or can't get to one. A repairer faces the ferrule square on a lathe, centres the tip and trims it in one set-up.

Take the cue to a shop if the ferrule end isn't flat, the ferrule is cracked or loose, the cue is valuable, or you are fitting an expensive layered tip for the first time. If you want to learn the job, do as Dr. Dave suggests and practise on an old cue first. Shaping, trimming a mushroomed edge and scuffing are different: they are cheap, low-risk and frequent, and every player should do them.

With the tip sorted, train the contact point

AimGeometry is a free pool trainer in your browser. The follow and draw lesson shows how hitting above or below centre changes where the cue ball goes, and tells you after every shot how far off you were. It does not simulate miscues, so a well-kept tip is still your job at the table.

Try the follow and draw lesson →

FAQ

How do I know when my cue tip needs replacing?

Replace it when there is almost no leather left above the ferrule, when it splits or its layers separate, when it moves on the ferrule, or when scuffing no longer makes it hold chalk. A flat top, a shiny surface or a mushroomed edge can be fixed by reshaping, scuffing or sanding the side flush.

How often should you replace a cue tip?

There is no fixed interval; it depends on how much you play, how hard the tip is and how often you shape and scuff it. Dr. Dave Alciatore's FAQ says a hard tip, chalked before every shot and shaped as little as possible, can last several years of regular play.

Can you use super glue on a cue tip?

Yes. A cyanoacrylate (super glue) gel is what Dr. Dave Alciatore's hand method uses. Use fresh glue, the gel rather than the thin liquid, and press the tip on firmly and evenly until it sets. Contact-type tip cement is the older alternative and is applied differently.

How long do you hold a new cue tip while the glue sets?

Super glue gel sets in about a minute under firm, even pressure; give it the full cure time on the pack before playing hard shots. A contact tip cement is coated on both surfaces, left to turn tacky, pressed together and left for the time on its pack (ten minutes for the common ten-minute type).

Should a cue tip be dime or nickel shaped?

Use a curvature radius a little smaller than the tip's width: a dime (or UK 5p) for tips of about 10 mm, including snooker cues, a nickel for about 12 mm and a quarter for about 13 mm. For a given contact point every shape gives the same spin; the dome is there so the tip never meets the ball on its edge.

Is replacing a snooker cue tip any different?

The method is the same. Snooker tips are smaller, usually 9 to 10 mm, so take extra care not to scrape or sand the ferrule, and shape the dome to about a dime or 5p radius.

Advertisement

Related reading: Cue Tip Size and Hardness · Chalk and Tip Maintenance · Snooker Cue vs Pool Cue · Snooker Screw Shot · What Is English in Pool?

Sources: Dave Alciatore, ‘DIY Tip Replacement’, Billiards Digest, May 2021, and his handout ‘How to Replace a Cue Tip ... No Special Tools Required’ (billiards.colostate.edu), for the procedure, materials, oversized tip, ledge and mushrooming warnings and the advice to prefer a cue mechanic; drdavepoolinfo.com FAQ pages, read 17 November 2026: replacing a tip (cyanoacrylate gel, when to replace, tip life, contributor tips on moisture and pre-sealing the tip), cue tip mushrooming and caring for a tip (both quoting the rec.sport.billiard FAQ, including ‘tap more, scuff less’ and burnishing), cue tip size and shape (Patrick Johnson’s radius rule and miscue limit, flat-tip contact, centred crown) and hardness effects (shorter tips play harder, soft tips harden with use, hard tips hold their shape); Kamui tip installation guide (layer glue softens above 60 °C from friction heat); directions for contact-type ten-minute tip cement as printed on retailer listings; coin diameters from the US Mint and the Royal Mint. Replacement intervals from retailers are mentioned only as rules of thumb. This article contains no sponsored or affiliate links.

Advertisement